Serwis Infona wykorzystuje pliki cookies (ciasteczka). Są to wartości tekstowe, zapamiętywane przez przeglądarkę na urządzeniu użytkownika. Nasz serwis ma dostęp do tych wartości oraz wykorzystuje je do zapamiętania danych dotyczących użytkownika, takich jak np. ustawienia (typu widok ekranu, wybór języka interfejsu), zapamiętanie zalogowania. Korzystanie z serwisu Infona oznacza zgodę na zapis informacji i ich wykorzystanie dla celów korzytania z serwisu. Więcej informacji można znaleźć w Polityce prywatności oraz Regulaminie serwisu. Zamknięcie tego okienka potwierdza zapoznanie się z informacją o plikach cookies, akceptację polityki prywatności i regulaminu oraz sposobu wykorzystywania plików cookies w serwisie. Możesz zmienić ustawienia obsługi cookies w swojej przeglądarce.
With the trend of higher power density, miniaturization as well as higher operating temperature requirement, heat transfer problem has been one of the crucial issues. Microchannel heat sink shows a great potential regarding to the excellent heat dissipation capacity. This paper aims to design microchannel heat sink for high power modules cooling based on topology optimization method to obtain better...
By using the finite element thermal analysis method, the mode of the structure coupling analysis of the macro-micro motion platform is established, and the connecting frame and the thermal characteristic of the connecting frame and the flexible hinge platform is analyzed. It is found that the deformation amount of the connecting frame and the flexible hinge increases at the field load condition with...
In this paper, influences of the initial stress on the surface micromachining silicon nitride pressure sensor was analyzed and discussed. The residual stress in the diaphragm is a major issue that makes significant difference on the performance of surface micro machined pressure sensors, such as warpage, micro-cracking, delamination, debonding, and nonuniform stress profile of the membrane. The pressure...
The process of dispensing gel above the silicon chip aimed at protecting chip surface and bonding wire is one of the most critical steps in the production of highly accurate low-pressure sensor modules. Numerous research efforts focused on the influences of dispensing process parameters, configuration and mechanical behavior of cured gel on the performance of sensors, while few concerns were taken...
Graphene sheet (GS) is a two-dimensional (2D) material with extremely favorable mass sensor properties. In this paper, a linear elastic 2D plate model is applied to study the potential of a nanoscale mass sensor on individual GS. The simulated natural frequency was compared with the results obtained from the Rayleigh's energy method. The effects of the attached mass, aspect ratio, and the layer number...
The paper investigates the insertion force and contact reliability of N electric connector. A finite element model (FEM) of the contacts was created and simulation of the contact force was completed by ANSYS. Impact of the friction coefficient, shrink range, length of socket, and groove width on the insertion force was analyzed by changing the structural parameters. Variation curves of the insertion...
Graphene sheet (GS) is a two-dimensional (2D) material with extremely favorable mass sensor properties. In this paper, a linear elastic 2D plate model is applied to study the potential of a nanoscale mass sensor on individual GS. The simulated natural frequency was compared with the results obtained from the Rayleigh's energy method. The effects of the attached mass, aspect ratio, and the layer number...
In this paper, influences of the initial stress on the surface micromachining silicon nitride pressure sensor was analyzed and discussed. The residual stress in the diaphragm is a major issue that makes significant difference on the performance of surface micro machined pressure sensors, such as warpage, micro-cracking, delamination, debonding, and nonuniform stress profile of the membrane. The pressure...
The process of dispensing gel above the silicon chip aimed at protecting chip surface and bonding wire is one of the most critical steps in the production of highly accurate low-pressure sensor modules. Numerous research efforts focused on the influences of dispensing process parameters, configuration and mechanical behavior of cured gel on the performance of sensors, while few concerns were taken...
Quadrate Flat Package (QFP) is chosen as package mode of chip for typical Hall-effect current sensors. In this paper, taking the deformation behavior of QFD structure under the temperature loading into consideration, according to related physics laws such as Fourier heat transfer law, Stephen-Boltzmann law and Newton's law of cooling, the thermal simulation of packaging for current sensor is implemented...
With the current trend of cheaper, faster, and better electronic equipment, it has become increasingly important to evaluate the package and system performance very early in the design cycle using simulation tools [1]. Many studies have shown that the profile of temperature has a great impact on solder joint reliability. Undergoing the different temperature profile will get a different solder joint...
The attachment of the silicon piezoresistive pressure sensor die to the substrate is one of the most critical steps in the production of highly accurate pressure sensor. In this paper, single parameter of the adhesive affecting the silicon piezoresistive pressure sensor's output characteristics has been studied. Shear strength of the adhesive with optimized parameters also has been evaluated. Material...
Transient responses of 3D stacked-die package with through silicon via (TSV) structure under board level drop test load following the JEDEC standard are investigated using the Input-G finite element simulation method. In order to reduce the finite element mesh size the stacked-die package under investigation is modeled with details while the others are simplified as blocks with equivalent material...
Analytical solution is established to calculate equivalent thermal resistances of the through silicon via (TSV) structure in both z direction and x y directions and is verified by the finite element simulation. The effects of the structural parameters such as the thickness of die, the diameter of copper via and the pitch of the copper via on the equivalent thermal conductivity of composite TSV structure...
The piezoresistive pressure sensor is one of the major applications of MEMS (Micro-Electro-Mechanical-System) devices. Nowadays, in the field of automotive electronics, silicon-based pressure sensors are playing a significant role in the control of brake, engine, tire pressure, etc. The piezoresistive based engine oil pressure sensor mentioned in this paper is applied to detect the pressure of lubricant...
Thermo-mechanical reliability for 3D stacked-die package with through silicon via (TSV) is studied through finite element simulation with sub-modeling technology, and design of experiments (DoE) using Taguchi experiments and analysis method. Firstly, the thermo-mechanical responses of micro-solder joints between stacked-die and copper via/SiO2 insulated layer structures are investigated under accelerated...
A finite element model which includes electromigration, thermomigration, stress migration and concentration diffusion is established to study the mass diffusion phenomenon. Numerical experiment is carried out to obtain the electrical, thermal, stress and atomic concentration fields of the sweat and through silicon via (TSV) structure under high current density load. The effectiveness of the electromigration...
A finite element model which includes fluid flow, transport by diffusion, migration and convection, multiple species, and reactions is established to simulate the copper electrochemical deposition process in through silicon via (TSV) trench. The effects of fluid flow of the bulk copper electrolyte on the micro TSV trench have been investigated. The copper plating process in different TSV trench geometries...
Localized induction heating for wafer level packaging is discussed. This paper is to investigate the relationships between the geometry of solder loop and temperature distribution in induction heating. Using finite element method (FEM) and IR thermal imager, temperature distribution and variation are explored, which shows that the temperature on the solder loops is a function of the area and edge...
A nonlinear transient heat transfer finite element model based on commercial finite element software, ABAQUS, is developed to simulate the curing process of silicone adhesive. The curing reaction process and specific heat of the silicone adhesive were investigated using a differential scanning calorimetry (DSC) to obtain material parameters for numerical simulations. Curing reaction kinetics was derived...
Podaj zakres dat dla filtrowania wyświetlonych wyników. Możesz podać datę początkową, końcową lub obie daty. Daty możesz wpisać ręcznie lub wybrać za pomocą kalendarza.